Frigidaire FFTH1022U2 Guia de Instalação descarregar pdf

Hardware

.ytQ.oN

Centering/Support Blocks ( ” )

4 ” x 3 ” x 1

Stuffer Seal ( )

1” x 1 ” x 84”

Seal ( )

1” x 1 ” x 25”

Seal ( )

1” x 1 ” x 14”

Seal ( )

1” x 3/8” x 25”

Seal( )

1” x 3/8” x 14”

Seal ( )

1” x 3/4” x 14”

Hardware

Ground Wire (green)

.ytQ.oN

Trim Frame (top & bottom legs)

Grille Aluminum

Nuts (plastic)

Screw w/washer

Trim Frame (side legs)

Tooth washer for grounding screw

READ BEFORE INSTALLING UNIT

For Through-the-Wall Air Conditioners

Installation Instructions

NOTE:

DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED HERE

Note that the air conditioner dimensions are: 24" wide,14 " high, and 19" deep (without front). Install air conditioner

according to these installation instructions to achieve the best performance. Save these installation instructions for

future reference.

Do This First (for existing sleeve)

You may not need all parts in the kit. Discard unused parts.

Items in Kit

66129927394

INSTALLATION WARNINGS AND CAUTION

Carefully read the installation manual before beginning. Follow each step as shown.

Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.

Pay attention to danger and safety notices.

To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that

may be exposed.

Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and

install the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils.

To prevent injury or strain, use proper lifting and carrying techniques when moving unit.

Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over an extended

period of time.

Handle air conditioner with care.

Make sure air conditioner does not fall during installation.

Grounding Screw

1 2 3 4 5 6 7 8 9 10

Installation Instructions 1

Resumo do Conteúdo

Página 1 - Installation Instructions

Hardware32412345162378.ytQ.oN2Centering/Support Blocks ( ” )4 ” x 3 ” x 1 121212Stuffer Seal (

Página 2

10Trim Kit Installation Instructions1. Install the 1” x 1” x 84” long stuffer seal between the wall sleeve and the unit. A flat-bladed screwdr

Página 3

Common Wall-Sleeve DimensionsIMPORTANTAll wall sleeves used to mount the new air conditioner must be in sound structural condition and have a rear gri

Página 4

Existing Frigidaire sleeves may have older single sided intake grillesNew Dual Intake GrilleIMPORTANTThis units increased performance characteristics

Página 5

Grille RemovalImportant: Single intake grilles must be removed when used with dual intake Through-the-wall Units.Warning: When removing grilles, pr

Página 6

Alternate Installation OptionsNon-Directional GrillesUnit Mounted GrillesWhen installing a through-the-wall unit into a sleeve that utilizes a non-dir

Página 7

Direct Unit MountingIn cases where the dual intake grille cannot be mounted directly to the sleeve it is desirable to attach the grille to the back of

Página 8

Grille to Sleeve AttachmentIn cases where the dual intake grille fits inside the sleeve and the grille flange overlaps the sleeve flange, direct attac

Página 9

Non-Frigidaire Dual Intake GrilleIn cases where the existing sleeve is a non-Frigidaire sleeve but is installed with a dual intake grille. The existin

Página 10

Subsitute GrilleImportant: Single intake grilles must be removed when used with used with dual intake Through-the-wall Units. Installation of a stand